Whirlpool Dryer not Spinning? 6 Fixes

It’s a typical incident: you fill your dryer with wet towels only to realize that it won’t spin. So how do you tell what’s causing your Whirlpool dryer to stop spinning when there are so many possibilities?

The Whirlpool dryer may not be spinning because of an electrical issue with the circuit breakers and connections.

Most of the time, you can promptly handle these concerns by yourself, at little or no expense, from the comfort of your own home.

Whirlpool Dryer not Spinning: Top Causes

If your dryer starts, but the drum won’t spin, one of these common causes is blame.

The Drive Belt is Broken

The most common cause of a dryer not spinning is a broken drive belt. Turn the drum by hand to repair the problem. Because a functioning belt should give some resistance, the belt is most likely damaged if the drum rotates extremely readily and loosely. Remove the cover from your dryer and unplug it so you can check the belt to see if it’s damaged.

Drum Rollers Are Worn Out

On the rear of the drum, most whirlpool dryers have two drum support rollers, and some dryers also have two at the front. The motor may get overwhelmed, and the dryer will stop if these drum support rollers do not spin freely.

Remove the belt from the rear dryer and spin the drum by hand to check if the rollers are worn out. You may hear the dryer creating thumping noises when the support drum rollers wear down over time.

Damaged Idler Pulley

Another culprit for a still Whirlpool dryer is the idler pulley. This is one of the pulleys that helps spin the drum by suspending the driving belt and creating tension. Unfortunately, like the drive belt, the idler pulley can wear out over time or be destroyed by heavy loads.

Failure of the Drive Motor

A malfunctioning motor might also be the cause of a Whirlpool dryer not spinning. When this element fails, nothing happens – or, worse, the machine begins to make loud noises and harm other parts over time.

If your laundry comes out of the dryer sweaty or damp, the system may be shutting off during the cool-down period. This might happen when there are overheating issues, which a broken drive motor can cause.


Why won’t your Whirlpool Dryer Heat Up?

Guide to Fixing Whirlpool Dryer That wont Start

6 Fixes If Your Whirlpool Dryer Won’t Spin

  1. Fix the Broken Drive Belt

A broken drive belt may be resolved if you replace the old drive belt with a new unit, and there are several tutorials on YouTube that demonstrate how to do so (like this one). You’ll need some simple equipment which you can find at home.

First, Inspect the belt. Look for any wear, tear, breakages, etc. If it’s broken or worn, you’ll have to replace it.

Remove the four screws on the two brackets below the plate’s sides. These screws hold the dryer belt in place.

Open the back of the dryer. Cut excess material from both end of the belt, where it binds to the drum axles. It should be flat and opposite to the axles when clamped down.

Remove the screws if they’re worn. They’re at the end where the drum axles go into to keep it from spinning. Pull out on both sides just enough to slip off the old dryer belt, then connect new screws onto drum axles and make sure it’s properly placed before you tighten the clamps.

  1. Repair Drive Motor Failure

A malfunctioning motor is an easy find. Before removing anything from the cabinet space, turn off the power and disconnect the Whirlpool dryer from the outlets.

By following the cables up on top of your dryer’s interior, you should be able to reach a metal panel that covers the visible drive motor. You may need someone to assist you in keeping the panel in place while you remove it.

You should not attempt to repair it if it is visibly worn out; instead, replace it altogether. The cost ranges from $20 to $200 based on your Whirlpool dryer’s model and type.

  1. Replace the Drum Rollers

The drum rollers in a Whirlpool dryer ensure that the drum spins freely when drying clothes. If one roller is faulty and not spinning properly in your Whirlpool, it should be changed to maintain maximum performance.

Freely check the drum roller first to determine if they need to be replaced. You must then remove the dryer belt to check for worn drum support rollers.

Turn the drum by hand. If the drum doesn’t spin freely without the dryer belt, one or more of the rollers is likely worn and needs to be replaced. It would be best to replace both rollers at the same time.

  1. Replace the Broken Idler Pulley

If the drive belt is in good condition, but your Whirlpool dryer won’t spin, it could be due to an overloaded idler pulley. It puts strain on the drive belt, which may fail because of excessive friction caused by too much work.

If there are signs of damage or wear, such as bent metal edges or parts that do not freely turn as they did when new, accessing this inside cabinet part should reveal them.

This is a simple fix: just replace the idler pulley with a new one and it should start spinning again. Replacing the worn-out idler pulley will be more cost efficient than repairing it.

  1. Free the Dryer Drum From Any Obstruction

It’s possible that a Whirlpool Dryer won’t spin because the dryer drum is clogged with lint. So first, get your remaining laundry out of the appliance. Then, use a vacuum, an attached brush device on a power-stick hand vacuum, or an old brush to remove any loose dirt from the appliance interior. You may also use this method to remove lint from the filters.

Check the back seal of your Whirlpool dryer drum if you’ve cleaned the drum and filters but it still won’t spin. The seal may be worn and need to be replaced. To prevent future breakdowns, you can lubricate the seal frequently with silicone oil.

  1. Replace the Drum Bearing

Drum bearings are in charge of keeping the drum spinning and moving freely. If this element wears out or is broken, the appliance spin cycle’s ability will deteriorate, resulting in potential safety dangers such as fires caused by a lack of airflow.

Keep your ears open for any strange noises coming from behind there. If you hear a rumbling noise coming from your dryer, it’s probably time for the back drum bearing to be replaced.


It can be quite perplexing when the dryer drum stops spinning. Luckily, however, there are many quick checks and fixes you can perform yourself at home before calling a technician and spending extra money.

Leave a Comment

Your email address will not be published.