Whirlpool Cabrio Washer OL Error Code

Washing machines are hard to understand, and, quite frankly, it can be a bit too expensive to repair them. Fortunately, Whirlpool Cabrio washing machines are pretty popular, so it won’t be hard for you to get the needed help to handle an error code.

What’s even better is that OL error codes are relatively easy to fix, so you might not need to go as far as contacting customer service. We’ll tell you how to get a clear display and remove any error codes. Keep on reading to find out more details!

What Does the Code OL Error Mean On a Cabrio Washing Machine?

The Whirlpool Cabrio washer giving OL code indicates that you got the washer overloaded. At the beginning of each wash cycle, the inner tub fills with water. But if it’s overloaded to the extent that the inner basket can’t disengage from the motor, the drain pump sucks out water, and the wash cycle fails.

Consequently, the control of the washing machine detects the excessive load in the tub, and the OL message appears.

However, the overload isn’t only attributed to filling the whole basket; although it’s one possibility, these error codes could also signify a mechanical issue that’s jamming the tub to one side and making it difficult to move. As a result, the agitator will rotate independently from the basket.

Related

How Do You Clear the Fault Code OL on a Whirlpool Cabrio Washer?

As challenging as it can be, there’s a good chance you can get rid of the OL code without needing professional help. Here’s how:

Remove Excess Laundry

excess laundry

As mentioned earlier, the inner bearing of the basket is one thing that can cause the OL code. Therefore, your first attempt to clear the error code should be removing some clothes from the washer.

First, stop the washer after the drain cycle. Then, take out some items before you restart it. Don’t forget to add detergent because the washer draws out detergent as it drains the water, so you’ll need to replace it.

Examine the Basket

If you’re still getting the Whirlpool Cabrio washer error, you need to dissociate the Whirlpool Cabrio washing machine and inspect the basket. Most probably, you’ll find a coin or a sock lodged between the outer and the inner baskets. Otherwise, you may find rust in between, which creates the same problem. The following instructions will help you detach the basket.

  1. Turn off the washing machine.
  2. Unplug the power cord.
  3. Lift the top by inserting a knife or a small screwdriver below the panel while pushing it out of the seams, releasing the spring clips.
  4. Now that the inner tube is fully exposed, avoid breaking the glass lid as the top folds back. You’ll find a plastic top covering the tub, which you can remove and leave aside.
  5. Remove the snaps around the tub, and remove the hose connected to it as well.
  6. You should be able to locate the agitator and remove the cap covering to expose the center. Then, detach the center screw with your screwdriver.
  7. Using a pair of needle-nose pliers, pull away from the fins around the agitator to remove it.
  8. Carefully unscrew the plastic top gear, and make sure that the screws don’t fall into one of the slots in the basket.
  9. Remove the lower gear. And you may need to pull it off the splined shaft.
  10. Pull out the basket, which might be tricky if it’s rusty or corroded. Also, the liquid inside the basket is factory sealed, so don’t mind it.
  11. Get the basket totally cleaned, and ensure that nothing is clogging it.
  12. Lubricate the shaft and the basket. Afterward, put it back, and attach it in the reverse order.
  13. To check that it can easily float, pull on the basket at the top of the inside lips.

Appliance Repair

If you can’t eliminate the OL error code after you clean the tub, remove clogged items, and take away excess weight, get help from a home appliance technician.

How Do I Reset My Whirlpool Cabrio Washer?

Resetting the Cabrio washer can stop the OL error code, and it isn’t hard to tackle, so it’s worth trying.

  1. Turn off the washer.
  2. Set it to NORMAL mode.
  3. Turn the dial to the left (1 click).
  4. Turn the dial to the right (3 clicks).
  5. Now turn the dial to the left again (1 click).
  6. Then, turn the dial to the right one more time (1 click).
  7. Press “Start“, and wait for the lights to flash.
  8. Press the “Start / Stop” button.
  9. Rotate the dial, and all the lights should go off, including Wash, Rinse, and Stop.
  10. Turn off the washer.
  11. Unplug the washer for a few seconds.
  12. Plug the machine again and turn it back on.

Your machine is now reset. And you can run the necessary diagnostic tests or start a new cycle.

How to Troubleshoot the Whirlpool Cabrio Washer?

Whirlpool Cabrio Washer UL Error

The Whirlpool Cabrio troubleshooting process depends on the error code you get. There are several possibilities, some indicating an error with the wash cycle; others are related to the motor, the spin cycle, drainage, and so on.

Before troubleshooting or diagnostic procedures, check to see if the lid is closed adequately while using the washer. Also, ensure that you’re using the right amount of soap rather than using too much detergent.

If this fails, try resetting the washer, and then run the diagnostic test as we’ll detail. Then, except for the Power, Start, and Stop buttons, press and hold any button for 3 seconds. Then, release it for another 3 seconds, and repeat the process three times. If you don’t know how to fix the error code, contact your technician or the customer support team.

FAQs About Whirlpool Cabrio OL Error Code

Why Won’t My Whirlpool Cabrio Washer Fill With Water?

The low water level is significant for a water inlet malfunction; it could be clogged inlet hoses or a defective water inlet valve.

Why Isn’t My Whirlpool Washing Machine Going Into the Spin Cycle?

Falling to go into the spin cycle is mostly because of an issue with the door lock or the lid switch. Another less common explanation concerns improper loading of the clutch.

Wrap up

Falling to go into the spin cycle is mostly because of The Whirlpool Cabrio washer error code OL, which stands for “Overloaded.” However, this doesn’t always mean there’s an overload in the literal sense of the word.

To illustrate, that’s just how the control board translates the struggle to move the basket. So, be sure to follow the steps mentioned earlier to repair the overloaded machine. And if worse comes to worst, leave it to a home appliance technician to handle error codes and appliance repair.

Leave a Comment

Your email address will not be published. Required fields are marked *