Washer Not Filling With Water – Causes and Fixes

Having trouble with your washer not filling with water correctly? Tired of seeing heaps of dirty clothes everywhere? Worried about not finding an affordable repair guy?

Don’t fret, as we’re here to help guide you through the process of figuring out the problem and finding the perfect solution for it.

There are quite a few potential reasons as to why your washer is not filling up with water properly. The most common one being a broken water inlet valve that is responsible for a proper wash-and-rinse cycle.

If your washer is not filled up according to your need, start by asking yourself some obvious questions, like, is it plugged? is the water pressure of my house well, or is it low? Are the fill hoses bent at any angle that’s hindering the water flow?

By knowing the answers to such questions you can rule out many possibilities, leaving only a couple behind!

3 Most Common Reasons Why Your Washer Isn’t Filling With Water Properly + Solutions

using washing machine

There are three common reasons why a washer may not be filling up with water properly. We tackle each of these reasons below and present you with viable solutions.

Broken Water Inlet Valve

The water inlet valve manages the wash-and-cleanse pattern by allowing the water to enter and leave the machine. A shortage in the amount of water in the washer is due to an impaired valve.

By using a meter, make sure that the solenoids used in opening the valve are in continuity. If that’s the case, then the fault is in the valve and it should be replaced.

Water Temperature Switch

water temperature switch

Certain models of washers allow you to adjust the temperature of the water filling the machine. The switch is a major part that signals the inlet valve to pave a path for the cold and hot water to fill the appliance. If any error occurs in the switch, it results in the improper filling of the washer.

The preferable solution to this difficulty is to insert a new workable switch in place of the old one.

Malfunctioning Timer

The timer is an electronic control device within your washer that sends alerts to the inlet valve to allow the rushing in of water.

Run by a motor, the electrical contacts of the timer send a message to the circuit responsible for filling the tub.

Any defect in the main control board can damage the timer and result in your machine not filling up with water properly. To solve this issue, fix the problem occurring in the main control board or get the machine checked by a professional; the latter being the most optimal approach if you’re not well-versed with electronics.

FAQs

Here are some of the most frequent questions we’ve received with regard to the problem at hand.

What are some of the things to check when your washer is not filling with water?

Firstly, verify that the supply pipes for hot and cold water are connected and switched on. You should also inspect the inlet hose for kinks. Lastly, make sure that the drain hose is correctly installed.

How to prevent the drain hose of a washing machine from kinking?

There are many measures you can take to keep your washer from kinking. Firstly, you should keep a considerable distance between the water connection and the rear side of your washing machine.

Secondly, you should regularly examine the different hoses and replace them every 3-5 years as a precautionary measure.

Keeping the water valve turned off while you are away from home for an extended period is also very important.

What are some signs that you need to get a new washing machine?

The average lifetime of a washer is around 7 to 13 years. If your washer has been causing you some trouble recently, it might be nearing the end of its lifespan and it might be time for you to start saving up for a new machine. How do you know for sure, though? There are a few signs to look for!

If your washer is leaking even after you’ve checked the hoses and re-tightened them, this might be a sign that your tub is cracked, and getting it fixed would be heavier on your pockets than buying a new machine.

If your appliance is making a lot of noise, in most situations, it is due to the washer not being leveled on the ground. If that’s not the case, then tightening the drum or the motor mount is the only other solution.

Getting an estimate for each of these repair measures would help you decide whether or not upgrading would be a better option.

Conclusion

loading washine machine

A defective main control board, faulty timer, and damaged water temperature switch are some of the most probable causes of irregular water filling in a washing machine. Recognizing these faults at an early stage can save your appliance from possible damage in the future, which, in turn, will save your hard-earned money!

Leave a Comment

Your email address will not be published. Required fields are marked *